0、执行/usr/X11/bin/xorgconfig开始字符界面的Xorg Server配置；
========================================================================
# /usr/X11/bin/xorgconfig
========================================================================
1、如下屏幕，回车确定；
========================================================================
This program will create a basic xorg.conf file, based on menu selections
you make. This program will ask for a pathname when it is ready to write
the file.
The xorg.conf file usually resides in /etc/X11. If no xorg.conf file
is present there, Xorg will probe the system to autoconfigure itself.
You can run Xorg -configure to generate a xorg.conf file based on
the results of autoconfiguration, or let this program produce a base
xorg.conf file for your configuration and fine-tune it.
Before continuing with this program, make sure you know what video card
you have, and preferably also the chipset it uses and the amount of video
memory on your video card, as well as the specifications of your monitor.
Press enter to continue, or ctrl-c to abort.
========================================================================
2、选择鼠标，1或5都可以；
========================================================================
First specify a mouse protocol type. Choose one from the following list:
The recommended protocol is Auto. If you have a very old mouse
or don't want OS support or auto detection, and you have a two-button
or three-button serial mouse, it is most likely of type Microsoft.
Enter a protocol number:
========================================================================
2.1、是否模拟三键鼠标，是；
========================================================================
If your mouse has only two buttons, it is recommended that you enable
Emulate3Buttons.
Please answer the following question with either 'y' or 'n'.
========================================================================
2.2、选择鼠标设备，回车使用默认的/dev/mouse(或/dev/kdmouse)；
========================================================================
Now give the full device name that the mouse is connected to, for example
/dev/tty00. Just pressing enter will use the default, /dev/mouse.
Mouse device:
========================================================================
3、选择键盘设备，5678均可，建议选7；
========================================================================
description of your keyboard. If nothing really matches,
choose 1 (Generic 101-key PC)
1 Sun Type 6 USB
2 Sun Type 6 USB (European layout)
3 Sun Type 6 USB (Japanese layout)
4 Sun Type 6 USB (Unix layout)
5 Generic 101-key PC
6 Generic 102-key (Intl) PC
7 Generic 104-key PC
8 Generic 105-key (Intl) PC
9 Sun Type 4
10 Sun Type 4 (Canadian layout)
11 Sun Type 4 (Japanese layout)
12 Sun Type 4 (European layout)
13 Sun Type 5
14 Sun Type 5 (European layout)
15 Sun Type 5 (Japanese layout)
16 Sun Type 5 (Unix layout)
Enter a number to choose the keyboard.
Press enter for the next page
========================================================================
3.1、选择键盘布局，选1；
========================================================================
1 U.S. English
2 U.S. English w/ ISO9995-3
3 U.S. English w/ deadkeys
4 Albanian
5 Arabic
6 Armenian
7 Azerbaijani
8 Belarusian
9 Belgian
10 Bengali
11 Bosnian
12 Brazilian
13 Bulgarian
14 Burmese
15 Canadian
16 French Canadian
17 Croatian
18 Croatian (US)
Enter a number to choose the country.
Press enter for the next page
========================================================================
3.2、回车确认；
========================================================================
Please enter a variant name for 'us' layout. Or just press enter
for default variant
========================================================================
3.3、是否使用XKB管理键盘输入，建议选是；
========================================================================
Please answer the following question with either 'y' or 'n'.
Do you want to select additional XKB options (group switcher,
group indicator, etc.)?
Enter your choice:
========================================================================
4、显示器(Monitor)设置，回车继续；
========================================================================
Now we want to set the specifications of the monitor. The two critical
parameters are the vertical refresh rate, which is the rate at which the
the whole screen is refreshed, and most importantly the horizontal sync rate,
which is the rate at which scanlines are displayed.
The valid range for horizontal sync and vertical sync should be documented
in the manual of your monitor. If in doubt, check the monitor database
/usr/X11/share/doc/Monitors to see if your monitor is there.
Press enter to continue, or ctrl-c to abort.
========================================================================
4.1、选择显示器类型，(800x600建议选2，1024x768建议选6-7)；
========================================================================
You must indicate the horizontal sync range of your monitor. You can either
select one of the predefined ranges below that correspond to industry-
standard monitor types, or give a specific range.
It is VERY IMPORTANT that you do not specify a monitor type with a horizontal
sync range that is beyond the capabilities of your monitor. If in doubt,
choose a conservative setting.
hsync in kHz; monitor type with characteristic modes
1 31.5; Standard VGA, 640x480 @ 60 Hz
2 31.5 - 35.1; Super VGA, 800x600 @ 56 Hz
3 31.5, 35.5; 8514 Compatible, 1024x768 @ 87 Hz interlaced (no 800x600)
4 31.5, 35.15, 35.5; Super VGA, 1024x768 @ 87 Hz interlaced, 800x600 @ 56 Hz
5 31.5 - 37.9; Extended Super VGA, 800x600 @ 60 Hz, 640x480 @ 72 Hz
6 31.5 - 48.5; Non-Interlaced SVGA, 1024x768 @ 60 Hz, 800x600 @ 72 Hz
7 31.5 - 57.0; High Frequency SVGA, 1024x768 @ 70 Hz
8 31.5 - 64.3; Monitor that can do 1280x1024 @ 60 Hz
9 31.5 - 79.0; Monitor that can do 1280x1024 @ 74 Hz
10 31.5 - 82.0; Monitor that can do 1280x1024 @ 76 Hz
11 Enter your own horizontal sync range
Enter your choice:
========================================================================
4.2、选择显示器刷新频率，建议选2；
========================================================================
You must indicate the vertical sync range of your monitor. You can either
select one of the predefined ranges below that correspond to industry-
standard monitor types, or give a specific range. For interlaced modes,
the number that counts is the high one (e.g. 87 Hz rather than 43 Hz).
1 50-70
2 50-90
3 50-100
4 40-150
5 Enter your own vertical sync range
Enter your choice:
========================================================================
5、选择显卡类型，输入一个描述符，可以直接回车继续；
========================================================================
You must now enter a few identification/description strings, namely an
identifier, a vendor name, and a model name. Just pressing enter will fill
in default names.
The strings are free-form, spaces are allowed.
Enter an identifier for your monitor definition:
========================================================================
5.1、是否查看显卡模块数据库选择一个合适的模块，是(输入yes)；
========================================================================
Now we must configure video card specific settings. At this point you can
choose to make a selection out of a database of video card definitions.
Because there can be variation in Ramdacs and clock generators even
between cards of the same model, it is not sensible to blindly copy
the settings (e.g. a Device section). For this reason, after you make a
selection, you will still be asked about the components of the card, with
the settings from the chosen database entry presented as a strong hint.
The database entries include information about the chipset, what driver to
run, the Ramdac and ClockChip, and comments that will be included in the
Device section. However, a lot of definitions only hint about what driver
to run (based on the chipset the card uses) and are untested.
If you can't find your card in the database, there's nothing to worry about.
You should only choose a database entry that is exactly the same model as
your card; choosing one that looks similar is just a bad idea (e.g. a
GemStone Snail 64 may be as different from a GemStone Snail 64+ in terms of
hardware as can be).
Do you want to look at the card database?
========================================================================
5.2、回车到第二页，找到Vmware一项，或直接输入对应序号 "29" ；
========================================================================
18 ** NVIDIA (generic) [nv] -
19 ** NeoMagic (generic) [neomagic] -
20 ** Number Nine I128 (generic) [i128] -
21 ** Rendition (generic) [rendition] -
22 ** S3 (not ViRGE or Savage) (generic) [s3] -
23 ** S3 Savage (generic) [savage] -
24 ** S3 ViRGE (generic) [s3virge] -
25 ** SiS (generic) [sis] -
26 ** Silicon Motion (generic) [siliconmotion]-
27 ** Trident (generic) [trident] -
28 ** Tseng Labs (generic) [tseng] -
29 ** VMWare guest OS (generic) [vmware] -
30 2 the Max MAXColor S3 Trio64V+ -
31 2-the-Max MAXColor 6000 ET6000
32 3DLabs Oxygen GMX PERMEDIA 2
33 928Movie S3 928
34 AGX (generic) AGX-014/15/16
35 ALG-5434(E) CL-GD5434
========================================================================
5.3、确认选择的Xorg显示驱动模块"Vmware"，直接回车继续；
========================================================================
Enter a number to choose the corresponding card definition.
Press enter for the next page, q to continue configuration.
Press enter to continue, or ctrl-c to abort.
========================================================================
5.4、再次要求输入显卡描述符(将记录在配置文件中)，输入"vmware"；
========================================================================
You must now enter a few identification/description strings, namely an
identifier, a vendor name, and a model name. Just pressing enter will fill
in default names (possibly from a card definition).
Your card definition is ** VMWare guest OS (generic) [vmware].
The strings are free-form, spaces are allowed.
Enter an identifier for your video card definition:
========================================================================
5.5、选择显存大小，任意(测试1\5\6均可)；
========================================================================
Now you must give information about your video card. This will be used for
the "Device" section of your video card in xorg.conf.
It is probably a good idea to use the same approximate amount as that detected
by the server you intend to use. If you encounter problems that are due to the
used server not supporting the amount memory you have, specify the maximum
amount supported by the server.
How much video memory do you have on your video card:
Enter your choice:
========================================================================
6、配置显示分辨率模式段，Xorg允许指定一个色彩模式下的多种分辨率，并在运行时自动匹配；
默认设置如下面显示的，如果不想使用那么大的分辨率必须手工设定分辨率模式；例如希望使用
800x600x24bpp，则需选择"3"，配置24-Bit模式下的期望分辨率；
========================================================================
For each depth, a list of modes (resolutions) is defined. The default
resolution that the server will start-up with will be the first listed
mode that can be supported by the monitor and card.
Currently it is set to:
"1280x1024" "1024x768" "800x600" "640x480" for 8-bit
"1280x1024" "1024x768" "800x600" "640x480" for 16-bit
"1280x1024" "1024x768" "800x600" "640x480" for 24-bit
Modes that cannot be supported due to monitor or clock constraints will
be automatically skipped by the server.
1 Change the modes for 8-bit (256 colors)
2 Change the modes for 16-bit (32K/64K colors)
3 Change the modes for 24-bit (24-bit color)
4 The modes are OK, continue.
Enter your choice: 3
========================================================================
6.1、选择对应色彩模式下的分辨率，可以使用多个数字一次选择，则自动匹配分辨率时会根据
硬件情况由最前面的往后依次测试选择最合适的分辨率；如例中选择"432"，则默认分辨率为
1024x768，不成功则自动匹配800x600... 推荐选择固定值"3"或"4"；
========================================================================
Select modes from the following list:
1 "640x400"
2 "640x480"
3 "800x600"
4 "1024x768"
5 "1280x1024"
6 "320x200"
7 "320x240"
8 "400x300"
9 "1152x864"
a "1600x1200"
b "1800x1400"
c "512x384"
d "1400x1050"
Please type the digits corresponding to the modes that you want to select.
For example, 432 selects "1024x768" "800x600" "640x480", with a
default mode of 1024x768.
Which modes? 3
========================================================================
6.2、X允许使用大于真实分辨率的虚拟桌面，使用鼠标在边缘平移来滚动桌面，建议选否 "n"；
========================================================================
You can have a virtual screen (desktop), which is screen area that is larger
than the physical screen and which is panned by moving the mouse to the edge
of the screen. If you don't want virtual desktop at a certain resolution,
you cannot have modes listed that are larger. Each color depth can have a
differently-sized virtual screen
Please answer the following question with either 'y' or 'n'.
Do you want a virtual screen that is larger than the physical screen? n
========================================================================
6.3、依次选取各显示模式的分辨率后，选择"4"确认；
========================================================================
Modes that cannot be supported due to monitor or clock constraints will
be automatically skipped by the server.
1 Change the modes for 8-bit (256 colors)
2 Change the modes for 16-bit (32K/64K colors)
3 Change the modes for 24-bit (24-bit color)
4 The modes are OK, continue.
Enter your choice: 4
========================================================================
6.4、选择默认的色彩深度，根据我们期望的显示模式，选择 "5"，24Bit显示；
========================================================================
Please specify which color depth you want to use by default:
Enter a number to choose the default depth.
========================================================================
7、"y"保存。(如果不想直接保存到系统配置文件，可以选择"n"然后在下一步中保存到其它路径。)
========================================================================
I am going to write the xorg.conf file now. Make sure you don't accidently
overwrite a previously configured one.
Shall I write it to /etc/X11/xorg.conf? y
========================================================================
8、重新启动系统，或直接启动图形界面。
========================================================================
# sync && reboot
